EPA 608 Practice Test Type 1

📌 Want quick access for next time? Bookmark now — Desktop: Ctrl/Command + D. Mobile: Menu (⋮ or Share) → Add to Bookmarks/Home.

If you’re preparing for certification to service small appliances, this EPA 608 practice test Type 1 is the right place to begin. You’ll answer 35 required questions covering safety procedures, environmental rules, recovery techniques, and regulatory knowledge. This section gives you a focused way to test your skills and review important topics before moving forward to more advanced systems.

35 Questions

1. What is the refrigerant charge limit for equipment to qualify as a small appliance?

 
 
 
 

2. Why must refrigerant be weighed during charging?

 
 
 
 

3. Why is evacuation important before recharging a system with refrigerant

 
 
 
 

4. Which EPA regulation applies to the design of recovery equipment used with small appliances?

 
 
 
 

5. What is the purpose of performing a standing pressure test after a repair?

 
 
 
 

6. What must be done before charging a system that has been opened for servicing?

 
 
 
 

7. What is the most common method for detecting leaks in a small appliance system?

 
 
 
 

8. What documentation is recommended after completing refrigerant recovery and recharging?

 
 
 
 

9. Which type of recovery device is commonly used for small appliances?

 
 
 
 

10. Which type of container must be used when storing recovered refrigerant from small appliances?

 
 
 
 

11. Why is using compressed air to pressurize a refrigeration system considered unsafe?

 
 
 
 

12. Which of the following is NOT considered a small appliance?

 
 
 
 

13. What is the EPA-required final vacuum level when evacuating a small appliance using recovery equipment manufactured after November 15, 1993?

 
 
 
 

14. Technicians must NOT use system-dependent recovery equipment when:

 
 
 
 

15. All the following are examples of small appliances EXCEPT:

 
 
 
 

16. What is the preferred method of adding refrigerant to a small appliance system under deep vacuum?

 
 
 
 

17. What happens if a technician attempts to evacuate a system with a large leak?

 
 
 
 

18. What step should follow immediately after a system is fully recharged?

 
 
 
 

19. According to the EPA, small appliances must be:

 
 
 
 

20. If a technician is using recovery equipment manufactured before November 15, 1993, what is the minimum evacuation requirement for small appliances?

 
 
 
 

21. When recharging a small appliance, where should refrigerant be introduced if system pressure is below atmospheric?

 
 
 
 

22. When using recovery equipment on a small appliance, the technician must ensure:

 
 
 
 

23. What must always be used when pressurizing a system with nitrogen?

 
 
 
 

24. What is the primary purpose of using a recovery device when servicing small appliances?

 
 
 
 

25. Which gas is approved for pressurizing a small appliance to check for leaks?

 
 
 
 

26. What component stores recovered refrigerant during the service process?

 
 
 
 

27. Before using a system-dependent recovery device, what must be checked?

 
 
 
 

28. Why should technicians wait a few minutes after reaching the required vacuum before opening the system?

 
 
 
 

29. A system-dependent recovery unit:

 
 
 
 

30. Why does the EPA define small appliances separately from other systems?

 
 
 
 

31. How can a technician confirm that liquid refrigerant has been fully recovered from a small appliance?

 
 
 
 

32. Which of the following qualifies as a small appliance under EPA Section 608?

 
 
 
 

33. What tool is used to verify that a system has been properly evacuated?

 
 
 
 

34. What must a technician do if unable to achieve the required vacuum level due to a system leak?

 
 
 
 

35. When checking for leaks after a repair, how long should the system maintain pressure to confirm integrity?

 
 
 
 


Completing the EPA 608 practice test Type 1 gives you a solid review of small appliance guidelines and technician responsibilities. With 35 questions covering EPA rules and safe service practices, this section is a vital step toward your full certification. Take note of the explanations provided so you can learn from any mistakes. Once you’re confident here, continue to the Type 2 practice test to expand your knowledge to high- and very high-pressure systems.

Next: EPA 608 Type 2 Practice Test
Mark A. Fletcher
Latest posts by Mark A. Fletcher (see all)