EPA 608 Practice Test Type 3

📌 Want quick access for next time? Bookmark now — Desktop: Ctrl/Command + D. Mobile: Menu (⋮ or Share) → Add to Bookmarks/Home.

This EPA 608 Type 3 practice test centers on low-pressure systems and the specific procedures involved in servicing them. It consists of 40 questions covering essential knowledge of recovery levels, allowable leak detection methods, low-pressure system recharging, and EPA regulations. Use this test to build on your knowledge and feel confident that you will be prepared for Type 3 certification.

40 Questions

1. What should a technician do if system pressure rises after evacuation during chiller disposal?

 
 
 
 

2. If a system exceeds the EPA leak rate threshold, how many days does a technician have to complete the repair?

 
 
 
 

3. When must follow-up leak inspections be conducted after a repair on a system containing over 50 pounds of refrigerant?

 
 
 
 

4. What is the primary challenge when recovering refrigerant from low-pressure appliances?

 
 
 
 

5. What is the primary reason for pulling a deep vacuum on a low-pressure system?

 
 
 
 

6. Which system is most likely to use a low-pressure refrigerant?

 
 
 
 

7. What happens if a low-pressure system contains water and the vacuum is pulled too quickly?

 
 
 
 

8. Why are low-pressure systems more likely to leak air into the system?

 
 
 
 

9. How long do technicians have to repair a leak after it is discovered in a commercial low-pressure system?

 
 
 
 

10. For industrial process refrigeration (IPR) systems, what is the maximum allowable annual leak rate before repairs are mandatory?

 
 
 
 

11. What is the required vacuum level for recovering refrigerant from a low-pressure appliance with a recovery device made after November 15, 1993?

 
 
 
 

12. What is the EPA leak rate threshold for comfort cooling appliances containing more than 50 pounds of refrigerant?

 
 
 
 

13. Which leak detection method is most commonly used for low-pressure centrifugal chillers?

 
 
 
 

14. Which of the following is a potential safety hazard when heating a low-pressure system to speed recovery?

 
 
 
 

15. Why should oil be warmed before evacuation in low-pressure systems?

 
 
 
 

16. What type of records must be maintained for leak inspections and repairs?

 
 
 
 

17. Why is it important to isolate a low-pressure system from the vacuum pump after evacuation?

 
 
 
 

18. What is the EPA-required evacuation level for low-pressure appliances using recovery or recycling equipment manufactured after November 15, 1993?

 
 
 
 

19. What is the EPA-required vacuum level when recovering refrigerant from a low-pressure appliance for disposal?

 
 
 
 

20. Which component helps prevent system damage during refrigerant recovery by releasing pressure if it becomes excessive?

 
 
 
 

21. Which of the following must be documented in leak repair records?

 
 
 
 

22. When must a technician perform a follow-up verification test after a successful leak repair?

 
 
 
 

23. What is the purpose of hydrostatic tube testing in low-pressure systems?

 
 
 
 

24. What is the EPA leak repair threshold for comfort cooling low-pressure appliances?

 
 
 
 

25. Low-pressure refrigerants operate with what kind of pressure during normal system operation?

 
 
 
 

26. Which of the following is true about the boiling point of low-pressure refrigerants?

 
 
 
 

27. Before disposing of a low-pressure appliance, what must a certified technician do?

 
 
 
 

28. When removing refrigerant from a low-pressure system, what part of the system is evacuated last?

 
 
 
 

29. Which of the following is a common refrigerant used in low-pressure appliances?

 
 
 
 

30. What is a major danger of using oxygen or compressed air during leak testing?

 
 
 
 

31. During recovery from a low-pressure chiller, what is the typical temperature of the water used to aid refrigerant removal?

 
 
 
 

32. According to EPA regulations, what is the required evacuation level for low-pressure appliances using equipment manufactured after November 15, 1993?

 
 
 
 

33. What must be done if the annual leak rate exceeds the EPA threshold?

 
 
 
 

34. What method can speed up the recovery process from a low-pressure appliance?

 
 
 
 

35. What EPA regulation applies when a leak is detected in a low-pressure system with more than 50 pounds of refrigerant?

 
 
 
 

36. Why must technicians be cautious when recovering liquid refrigerant from a chiller under low ambient conditions?

 
 
 
 

37. When using a pressurizing agent to leak test an idle low-pressure appliance, which gas is acceptable?

 
 
 
 

38. What does the EPA require before opening a low-pressure system for maintenance?

 
 
 
 

39. What is the typical method used to speed up refrigerant recovery from a low-pressure system?

 
 
 
 

40. What helps reduce recovery time when evacuating refrigerant from a low-pressure appliance?

 
 
 
 


This Type 3 practice test emphasizes low-pressure systems, including key service practices, recovery procedures, and EPA-mandated guidelines. All 40 questions are required, so take your time to complete them thoroughly. Use this practice test to help you feel more confident before your actual certification exam.

Mark A. Fletcher
Latest posts by Mark A. Fletcher (see all)